Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Coil sleeve (plastic tubing) is the most commonly used size on all machines.
Cabinet flipper leaf switch assembly for most non-solid state flipper circuits.
NOVUS 2 Fine Scratch Remover polish
Flipper rebuild kits for late model Sega & post 2000 Stern pinball machines includes...
Common solenoid coil with no diode.
Common solenoid coil used on many manufacturers pinball machines.
Coil stop assembly used in flipper assemblies (500-5944-XX) in Sega/Stern games.
Universal fit black rubber tip for use on all ball shooter rods.
Plunger and link assembly for many Williams/Bally and other manufacturer p...
Pin-Buddy™ combo kit
Leg - 30-1/2 inch black textured
Shorter barrel spring for ball shooter assembly on all Data East, Sega, an...
Rubber grommet used on many Vertical Up Kicker (VUK) and Knocker assemblies.
Pinball Event Tune-Up Kit
Standard pop bumper base
Spring washer 1/2 inch inner diameter and 3/4 inch outer diameter commonly used on...
Pin-Buddy™ Game Saver Cantraption&tm 45°
USE 77-PCR
Elastic Stop Nut used on rod and ring (A-4754) assemblies.
Hole guard - switch slot 1-1/4 inch
Flat washer used in ball shoooter assemblies .390 x .625 x .059 inch.
Complete shooter assembly includes housing, shooter rod, inner green spring.
White 3 inch molded flipper with a 2-2/16 inch shaft...
Standard snap-in Nyliner® bearing bushing with 1/4 inch Inner Diameter
Coil - solenoid flipper Stern no diode
Nylon coil sleeve, 1-7/8 inch long with 3/16 inch flange.
Sega/DE/Stern Lift Trim is 26-1/16 inch long with 3/16 inch channel.
Lamp socket with bracket holds wedge based bulbs such as #555
Elastic stop nut used on the thumper bumper brackets and other mechanisms.
Mini spotlight reflector cover for lamp socket assemblies
Plunger and link assembly for Data East/ Sega / Stern flipper assemblies.
Flipper bushing DE/Sega/Stern 1/4 inch ID notched
Left plunger, link and crank (pawl) assembly used on all new Stern1 games
Node board 48 volt 8 driver Stern SPIKE 2
Ball shooter rod for Capcom / Data East / Sega / Stern pinball machines.
Guard - shooter lane Stern
Spring used on relay for VUK and Lazer Kicker.
E-clip or e-ring commonly used on many 3/16" mechanism shafts
Lamp socket fits #44 and #47 lamps. Staple down style with lugs.
2.69 inch overall length coil sleeve with 0.187 inch shoulder.
Right plunger, link and crank (pawl) assembly used on all new Stern1 games...
Normally Closed EOS (end-of-stroke) leaf switch used in Stern flipper a...
Vertical Up Kicker (VUK) sub-mini snap action microswitch
Pin-Buddy™ Game Saver Cantraption™ 180°
Data East\Stern pop bumper body.Substitute for 03-7443-5.
Flipper return spring for DE/Sega/Stern flipper assemblies. Reference:...
Coil support bracket.
Shielded 4 inch diameter speaker - 8 ohm 4 watt.
Black rubber push-in plug bumper with 1 inch diameter
Machine screw 8-32 X 1/4" pan head phillips sems. Many applications. Used...
Machine screw 8-32 x 3/8 inch phillips pan head.
Machine screw with 6-32 thread and 3/8 inch long with phillips pan head.
Trim playfield glass 20-3/8 x 1/2 inches Sega
Slingshot arm assembly for Stern, Sega, Data East and other games...
LED lamp #44 base white dual chip
Opto transmitter board SPIKE
Node board CPU Stern SPIKE II 60hz
Steel and nylon plunger assembly for VUK (Vertical UpKicker) assemblies
Drop target reset assembly assembly spring.
