Insider Connected™ upgrade kit for Stern Pinball Pro SPIKE 2 system pinball machines.
Coil sleeve (plastic tubing) is the most commonly used size on all machines.
Cabinet flipper leaf switch assembly for most non-solid state flipper circuits.
Commonly used pop bumper skirt, or wafer, used in all contemporary machines
Flipper rebuild kits for late model Sega & post 2000 Stern pinball machines includes...
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Common solenoid coil used on many manufacturers pinball machines.
Black plastic cashbox used in most solid state pinball machines
Coil stop assembly used in flipper assemblies (500-5944-XX) in Sega/Stern games.
Standard flipper rubber 0.5 x 1.5 in ID, black...
Universal fit black rubber tip for use on all ball shooter rods.
Leg - 30-1/2 inch black textured
Pin-Buddy™ combo kit
Spring - compression pop bumper 10A-7
Shorter barrel spring for ball shooter assembly on all Data East, Sega, an...
Rubber grommet used on many Vertical Up Kicker (VUK) and Knocker assemblies.
Standard pop bumper base
Spring washer 1/2 inch inner diameter and 3/4 inch outer diameter commonly used on...
Pin-Buddy™ Game Saver Cantraption&tm 45°
High tension spring used on pinball machine ball shooter assemblies. .038 inch
Sega / Data East / Stern Playfield black plastic playfield glass support R...
E-clip or e-ring commonly used on many mechanisms. 20A-8712-25 270-5002-00
Pinball Event Tune-Up Kit
Standard snap-in Nyliner® bearing bushing with 1/4 inch Inner Diameter
Coil - solenoid flipper Stern no diode
Williams/Bally pop bumper plunger. Reference: 02-3406-1 2A-340...
Flipper bushing DE/Sega/Stern
Ball shooter rod for Capcom / Data East / Sega / Stern pinball machines.
Guard - shooter lane Stern
Spring used on relay for VUK and Lazer Kicker.
E-clip or e-ring commonly used on many 3/16" mechanism shafts
Yellow 3 inch molded flipper and shaft assembly with 2-3/16 inch (55mm) shaft...
Node board 48 volt 8 driver Stern SPIKE 2
2.69 inch overall length coil sleeve with 0.187 inch shoulder.
Right plunger, link and crank (pawl) assembly used on all new Stern1 games...
Normally Closed EOS (end-of-stroke) leaf switch used in Stern flipper a...
Pin-Buddy™ Game Saver Cantraption™ 180°
Rubber O ring with 2-1/2 inch Inner Diameter. Reference Numbers: Gottlieb...
Data East\Stern pop bumper body.Substitute for 03-7443-5.
Flipper return spring for DE/Sega/Stern flipper assemblies. Reference:...
Shielded 4 inch diameter speaker - 8 ohm 4 watt.
Shaker and spinning disc replacement motor for Stern SAM, SPIKE, & SPIKE 2, Chicago Gaming...
Black rubber push-in plug bumper with 1 inch diameter
Black rubber O ring with 3/4 ubcg inner diameter. Reference Numbe...
Black rubber O ring with 1 inch inner diameter. Reference Nu...
Powder coat black side rail for new Stern pinball machines. Fits left or...
Trim playfield glass 20-3/8 x 1/2 inches Sega
#6-32 x 1-3/16 inch steel spiral fin shank screw used to secure pop bumper bra...
Metal yoke used in Data East, Sega, and Stern pop bumper assemblies.
Slingshot arm assembly for Stern, Sega, Data East and other games...
Opto transmitter board SPIKE
Metal post with hex base #6-32 tap and #10-32 thread on bottom.
Ball shooter housing includes housing and two 280-5010-00 Oil-lite bushing...
Lower pop bumper bracket and coil assembly fits Stern, Sega, Data East
1/4 inch hex spacer post - female/female 6-32 thread taps at bothe ends 3/4 inches long.
Protect plate for many sub-mini microswitch bodies.
End-of-stroke switch actuator arm for right side flipper assembly...
Flipper base plate with self tapping screws for Stern pinball machines - right side...
Coin door assembly Stern SPIKE System
Playfield bubble level with 6-1/2 degree markings