Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Standard carbon steel 1-1/16" diameter, 80 gram pinball
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
Standard pinball playfield tempered glass.
All-new flipper parts kit is the answer for sluggish flipper assemblies. 8/1993-10/1998
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
3 terminal, dual winding replacement flipper coil for the following Willia...
Williams / Bally regular cabinet stainless steel lockdown bar...
Standard 28-1/2 inch ribbed pinball machine leg with chrome plated finish for Williams...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Nylon flipper bushing is used on Williams Pinball games
Backbox lock and plate assembly for all of the Williams and Bally WPC syst...
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Replaced by 77-PCR
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Flipper return and drop target return spring
Williams original style white plastic pop bumper body
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
Pushbutton 1-1/8 inch red with internal spring
Metal yoke fits all pop bumper ring and rod assemblies.
Trough anti magnetic shim - Williams/Bally upgrade
Side rail set Williams/Bally 47 inch stainless
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Black lock with one key, lock washer, 1inch cam, and screw. Used for b...
WING SCREW or WING BOLT used on late model WPC system games.
Gray foam protector pre-cut pads commonly used in target switches...
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Red star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Williams / Bally style lane guide (also referred to as Rollover Guides, L...
Cashbox nest bracket Williams
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
Hole guard - switch slot 1-1/4 inch
Plunger assembly 3.375 inches no hole
Black 7/8 inch diameter corrugated plastic slit hose sleeve for wiring harness protection
Bell armature or plunger assembly for ball kickers and poppers
Upgraded Trough Assembly for Williams / Bally pinball machines
Williams/Bally opto board set
Elastic Stop Nut used on rod and ring (A-4754) assemblies.
Playfield side rail plastic molding is 42-1/4"
Infrared Transmitter assembly in the white plastic housing.
Knocker assembly kit for Bally and Williams AE-23-800
Clear tempered 27 x 18-7/8 x 1/8 inch thick glass
Pop bumper bracket used on Williams / Bally machines and other brands.
Glass corner protectors - Set of 2
E-clip or e-ring commonly used on many mechanisms. 20A-8712-25 270-5002-00
Common tilt plumb bob with 0.15 inch interior diameter for rod.
Back box toggle latch 20-9347 or tension latch