Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Barrel shaped, bright finish shooter spring used on many brand...
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
High quality steel plate replaces Bally / Williams part #01-11400-1
Flipper return and drop target return spring
Williams original style white plastic pop bumper body
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
Metal yoke fits all pop bumper ring and rod assemblies.
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
Gray foam protector pre-cut pads commonly used in target switches...
Spring - barrel compression shooter black
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
Pin-Buddy™ combo kit
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Williams / Bally black plastic drop target with 3/8" wide wedge shaped top...
Spring - barrel compression shooter brass
Cashbox nest bracket Williams
Medium-high tension spring used on pinball machine ball shooter assemblies.
Pinball Event Tune-Up Kit
Large twist-in socket for #906 wedge base lamps.
Plunger assembly 3.375 inches no hole
Bell armature or plunger assembly for ball kickers and poppers
Williams/Bally opto board set
Pin-Buddy™ Game Saver Cantraption&tm 45°
Transparent red eject hole shield plastic with 3/16" (0.1875") holes.
Elastic Stop Nut used on rod and ring (A-4754) assemblies.
Machine screw 6-32 thread x 1/4 inch long with phillips head and external tooth lock washer
Playfield side rail plastic molding is 42-1/4"
Hole guard - switch slot 1-1/4 inch
Solenoid coil no diode with straight terminals
Infrared Transmitter assembly in the white plastic housing.
Flat washer used in ball shoooter assemblies .390 x .625 x .059 inch.
Fits shaft diameter of 3/8 inch with groove diameter of 5/16 inch.
E-clip or e-ring commonly used on many mechanisms. 20A-8712-25 270-5002-00
Common tilt plumb bob with 0.15 inch interior diameter for rod.
Left side flipper unit Plunger- link-crank assembly
Flipper & shaft - Williams logo yellow
Machine Screw 6-32 x 3/8" long phillips pan head with external tooth lockw...
Ball Shooter Housing - Chrome. Reference: 21-6645-1
Wire 1/4" ground braid
Williams/Bally opto InfraRed transmitter board used in LED assembly A-1690...
New opto board 10 LED assembly. Replaces A-20246
Compression spring used on pop bumper assemblies and others.
Plunger & link assembly for later Bally and Williams machines.
Elastic stop nut used on the thumper bumper brackets and other mechanisms.
.156" spacing 12 position Insulation Displacement style connector
