Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Barrel shaped, bright finish shooter spring used on many brand...
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
3 terminal, dual winding flipper coil is used on the following games:...
Standard pinball playfield tempered glass.
Designed for non-Fliptronic® 2/1988 - 8/1991 Williams and Bally machines...
Cabinet flipper leaf switch assembly for most non-solid state flipper circuits.
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Backbox lock and plate assembly for all of the Williams and Bally WPC syst...
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Flipper return and drop target return spring
Standard Williams / Bally battery holder with through hole circuit board mount terminals.
Flipper & shaft - Williams logo white
Williams original style white plastic pop bumper body
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
Metal yoke fits all pop bumper ring and rod assemblies.
27 inch long Black Plastic LIFT TRIM used on the bottom of the backglass.
Black lock with one key, lock washer, 1inch cam, and screw. Used for b...
Plastic cube style, circuit board mounted DPDT (double pole, double throw)...
Gray foam protector pre-cut pads commonly used in target switches...
Spring - barrel compression shooter black
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
Pin-Buddy™ combo kit
Clear star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Spring - barrel compression shooter brass
Cashbox nest bracket Williams
Medium-high tension spring used on pinball machine ball shooter assemblies.
35 a wire lead bridge rectifier 5100-09690-00
Yellow wrapper 2.2 uF @ 250 volt axial lead non-polarized metalized polyester. 125-5002-00
Pinball Event Tune-Up Kit
Playfield glass protector black rubber grommet used on aprons
Large twist-in socket for #906 wedge base lamps.
Plunger assembly 3.375 inches no hole
Williams/Bally backglass trim. For games that use translites.
Pin-Buddy™ Game Saver Cantraption&tm 45°
Wire gate used on early solid state Williams ball trough runway assemblies
Elastic Stop Nut used on rod and ring (A-4754) assemblies.
AC Power Cord - 15 foot stripped end
Playfield side rail plastic molding is 42-1/4"
Hole guard - switch slot 1-1/4 inch
Solenoid coil no diode with straight terminals
Knocker assembly kit for Bally and Williams AE-23-800
Sub miniature snap action switch with 3 terminals and custom wireform.
Clear tempered 27 x 18-7/8 x 1/8 inch thick glass
