Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
Standard pinball playfield tempered glass.
All-new flipper parts kit is the answer for sluggish flipper assemblies. 8/1993-10/1998
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
3 terminal, dual winding replacement flipper coil for the following Willia...
Williams / Bally regular cabinet stainless steel lockdown bar...
Standard 28-1/2 inch ribbed pinball machine leg with chrome plated finish for Williams...
Backbox lock and plate assembly for all of the Williams and Bally WPC syst...
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Replaced by 77-PCR
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
High quality steel plate replaces Bally / Williams part #01-11400-1
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Flipper return and drop target return spring
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
Pushbutton 1-1/8 inch red with internal spring
27 inch long Black Plastic LIFT TRIM used on the bottom of the backglass.
Trough anti magnetic shim - Williams/Bally upgrade
Side rail set Williams/Bally 47 inch stainless
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Black lock with one key, lock washer, 1inch cam, and screw. Used for b...
Application Specific Integrated Circuit (ASIC) chip for Williams/Bally WPC
WING SCREW or WING BOLT used on late model WPC system games.
Gray foam protector pre-cut pads commonly used in target switches...
Reset Fix Board WPC Power Driver
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
Compression spring used in many different assemblies. Replaces 266-500...
New replacement WPC Type 2 Electronic / Opto flipper boards
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
Pin-Buddy™ combo kit
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Red star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Williams / Bally black plastic drop target with 3/8" wide wedge shaped top...
Cashbox nest bracket Williams
35 a wire lead bridge rectifier 5100-09690-00
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
Pinball Event Tune-Up Kit
Playfield glass protector black rubber grommet used on aprons
Pushbutton 1 inch round yellow 'Start'
Large twist-in socket for #906 wedge base lamps.
Black 7/8 inch diameter corrugated plastic slit hose sleeve for wiring harness protection
Connector rebuild kit - Williams WPC CPU board
Plunger assembly 3.375 inches no hole
Upgraded Trough Assembly for Williams / Bally pinball machines
Williams/Bally backglass trim. For games that use translites.
New flipper parts are the answer for sticky, sluggish, weak, or dead flippers.
Williams/Bally opto board set
