Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
Standard pinball playfield tempered glass.
All-new flipper parts kit is the answer for sluggish flipper assemblies. 8/1993-10/1998
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
3 terminal, dual winding replacement flipper coil for the following Willia...
Williams / Bally regular cabinet stainless steel lockdown bar...
Standard 28-1/2 inch ribbed pinball machine leg with chrome plated finish for Williams...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Replaced by 77-PCR
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
High quality steel plate replaces Bally / Williams part #01-11400-1
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Flipper return and drop target return spring
WPC Power Driver board rebuild kit
Flipper & shaft - Williams logo white
Williams original style white plastic pop bumper body
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
New style, black plastic, 3 AA cell, circuit board mounted battery holder.
Metal yoke fits all pop bumper ring and rod assemblies.
Trough anti magnetic shim - Williams/Bally upgrade
Side rail set Williams/Bally 47 inch stainless
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Application Specific Integrated Circuit (ASIC) chip for Williams/Bally WPC
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
WING SCREW or WING BOLT used on late model WPC system games.
Gray foam protector pre-cut pads commonly used in target switches...
Reset Fix Board WPC Power Driver
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
New replacement WPC Type 2 Electronic / Opto flipper boards
Pin-Buddy™ combo kit
Clear star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Cashbox nest bracket Williams
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
Pinball Event Tune-Up Kit
Large twist-in socket for #906 wedge base lamps.
Connector rebuild kit - Williams WPC CPU board
Black 7/8 inch diameter corrugated plastic slit hose sleeve for wiring harness protection
Plunger assembly 3.375 inches no hole
Upgraded Trough Assembly for Williams / Bally pinball machines
Bell armature or plunger assembly for ball kickers and poppers
Williams/Bally opto board set
Pin-Buddy™ Game Saver Cantraption&tm 45°
Elastic Stop Nut used on rod and ring (A-4754) assemblies.
