Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Standard carbon steel 1-1/16" diameter, 80 gram pinball
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
Standard pinball playfield tempered glass.
Coil sleeve (plastic tubing) is the most commonly used size on all machines.
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
3 terminal, dual winding replacement flipper coil for the following Willia...
Williams / Bally regular cabinet stainless steel lockdown bar...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Backbox lock and plate assembly for all of the Williams and Bally WPC syst...
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
High quality steel plate replaces Bally / Williams part #01-11400-1
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Flipper return and drop target return spring
Standard Williams / Bally battery holder with through hole circuit board mount terminals.
Williams original style white plastic pop bumper body
Metal Oxide Varistor (MOV), 130 Volt Used in the input power line.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
New style, black plastic, 3 AA cell, circuit board mounted battery holder.
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
Metal yoke fits all pop bumper ring and rod assemblies.
27 inch long Black Plastic LIFT TRIM used on the bottom of the backglass.
Refurbished Williams transformer with connectors. Reference: 5610-12...
Side rail set Williams/Bally 47 inch stainless
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Black lock with one key, lock washer, 1inch cam, and screw. Used for b...
Application Specific Integrated Circuit (ASIC) chip for Williams/Bally WPC
WING SCREW or WING BOLT used on late model WPC system games.
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Gray foam protector pre-cut pads commonly used in target switches...
Red transparent pop bumper cap
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Compression spring used in many different assemblies. Replaces 266-500...
Fiber yoke fits all pop bumper ring and rod assembles.
Reset Fix Board WPC Power Driver
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Standard backglass lift trim with 3/16 inch channel. Trim as needed. Used in...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Pin-Buddy™ combo kit
Williams / Bally black plastic drop target with 3/8" wide wedge shaped top...
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Spring - compression pop bumper 10A-7
Cashbox nest bracket Williams
Williams / Bally style lane guide (also referred to as Rollover Guides, L...
35 a wire lead bridge rectifier 5100-09690-00
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
Playfield glass protector black rubber grommet used on aprons
Williams/Bally backglass trim. For games that use translites.
Pushbutton 1 inch round yellow 'Start'