WING SCREW or WING BOLT used on late model WPC system games.
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
42 piece set of stainless steel hardware for late electromechanical and ea...
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Cashbox nest bracket Williams
Spring washer 1/2 inch inner diameter and 3/4 inch outer diameter commonly used on...
Tamper resistant head screw nail or spiral nail - 0.10 dia X 3/4 inch long
Flat washer used in ball shoooter assemblies .390 x .625 x .059 inch.
Common tilt plumb bob with 0.15 inch interior diameter for rod.
Back box toggle latch 20-9347 or tension latch
Cabinet protector - metal spacer - 4 piece set
Special short neck black carriage bolt for cabinet / backbox hinge.
Leg leveler - 3 inch long nylon base white
Clear polycarbonate fender washer for protection of slingshot posts
Pinball machine cabinet interior leg bolt mounting plate.
PAL nut 5/8 inch. Replaces 02-3000 & 240-5003-01
Pivot nut 7/8 inch
Rivnut hex 3/8-16 x .845 inch
Tilt plumb bob assembly
Graphite plumb bob used on many tilt switch assemblies.
Cable clamp 1 inch diameter single
Pivot nut 1/2 inch. Reference: 02-4329
Clear PETG copolyester fender washer for protection of slingshot posts
Tinnerman clip used to secured the plumb bob tilt on late model tilt assemblies.
Leg bolt 3/8-16 X 2-3/4 inch acorn head black
Bubble level vial commonly used in Williams / Bally pinball machines...
Backbox lock plate for Williams/Bally WPC System game backbox locks...
Flipper spring steel lever 4 inch
Hinge assembly upper insert
Pivot nut 11/16 inch
Hex spacer 1/4 x 1-1/4 inch f-f
Bally shooter lane arch bracket is made from pre-polished stainless steel...
Tilt bob assembly includes wire hook, plumb bob, and adjustable retainer c...
This is the left side Playfield Slide Assembly used on all late model Wil...
Washer 0.265 inch x .500 inch x .067 inch
Tamper resistant head screw or spiral nail 0.10 diameter X 1 inch
Tape - double sided 1 inch wide / per foot
Playfield prop up rod for early Bally pinball machines. Reference:...
Foam sponge washers for games such as Gottlieb HAUNTED HOUSE and BLACK HOLE.
Plate - spacer pinball machine cabinet slide. Reference: 01-11408
Bolt carriage 10-24 x 2-1/4 inch black
Plumb bob
Cable clamp 1/2 inch diameter single
Bracket clip for many late model Bally / Williams WPC machines. Refere...
Plumb bob tilt wire is used on many Bally Williams and other machines.
EZ slide & playfield support bracket set
New high quality brass finish 3/8-16 thread with 5/8" acorn head with 2-1/2 inch length.
Hair pin shaped cotter pin secures cash box lids. Zinc plated .093" d...
Bracket door release assembly for Bally DOCTOR WHO pinball machine
Lockbar receiver Stern games with center pushbutton
Cable clamp Holder 1/4" diameter
Playfield pivot for Williams machines. Reference: A-10959 playfie...
Circuit board mounting bracket for under playfield boards.
Hairpin clip Gottlieb
Cable clamp 3/4 inch diameter single
Lockbar receiver Stern no pushbutton
Hex head bolt with 3/8-16 thread and 2-1/2 inch overall length
Leg leveler - 3 inch chrome
