Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Standard carbon steel 1-1/16" diameter, 80 gram pinball
Heavy duty 3 prong grounded 15 amp 110v AC power cord replacement plug
Barrel shaped, bright finish shooter spring used on many brand...
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
Rubber - flipper 1/2 inch wide x 1-1/2 inch red
3 terminal, dual winding flipper coil is used on the following games:...
Standard pinball playfield tempered glass.
Standard keyed-alike single bit 7/8 inch long barrel lock with chrome bezel fi...
Designed for non-Fliptronic® 2/1988 - 8/1991 Williams and Bally machines...
Cabinet flipper leaf switch assembly for most non-solid state flipper circuits.
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Flipper end of stroke switch for electronic and electromechanical pinball machines.
Commonly used pop bumper skirt, or wafer, used in all contemporary machines
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Nylon flipper bushing is used on Williams Pinball games
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Replaced by 77-PCR
Key hook used on most coin door interiors.
Common solenoid coil with no diode.
Standard pinball machine leg leveler with 3/8 inch -16 thread and 3 inch long shaft
Ten-bulb box of #89 high quality miniature incandescent lamps.
Standard Williams / Bally battery holder with through hole circuit board mount terminals.
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Metal Oxide Varistor (MOV), 130 Volt Used in the input power line.
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
Metal yoke fits all pop bumper ring and rod assemblies.
Ten-bulb box of #906 High quality miniature incandescent lamp. May be replaced with 05-906W LED or 04-0912 bulbs.
Plunger and link assembly for many Williams/Bally and other manufacturer p...
Williams chrome plated legs with 9 inch support ribs used on many System 11 and 11B...
Plastic cube style, circuit board mounted DPDT (double pole, double throw)...
Gray foam protector pre-cut pads commonly used in target switches...
Spring - barrel compression shooter black
Pin-Buddy™ combo kit
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
Spring - barrel compression shooter brass
Pinball Event Tune-Up Kit
Yellow wrapper 2.2 uF @ 250 volt axial lead non-polarized metalized polyester. 125-5002-00
Hole guard - switch slot 1-1/4 inch
Pin-Buddy™ Game Saver Cantraption&tm 45°
Playfield side rail plastic molding is 42-1/4"
Glass corner protectors - Set of 2
New 3 bank Universal Drop Target Opto board is a one-size-fits-all, plug and play replacement.
Williams drop target opto transceiver
E-clip or e-ring commonly used on many mechanisms. 20A-8712-25 270-5002-00
Back box toggle latch 20-9347 or tension latch
Plunger assembly 3.875 inches ball popper
PS-12502-P Rev C display system for Williams system 11B and 11C
Common solenoid coil used on many manufacturers pinball machines.
Plastic, 3 clip, thumper bumper body used on mid 80's Bally pinball machines. C-970-5
Williams/Bally flipper coil stop. Reference:A-12111
Novelty 1-1/16' diameter pinball with black finish and eyeball design.Gr...
Flipper & shaft segmented ridges yellow
Cap for vertical upkicker (VUK) ball popper assembly sits on top of A-11336 plunger...
Universal snap action submicroswitch with 4 inch wire actuator that can be formed to various shapes.
