Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Standard carbon steel 1-1/16" diameter, 80 gram pinball
Barrel shaped, bright finish shooter spring used on many brand...
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
3 terminal, dual winding flipper coil is used on the following games:...
Standard pinball playfield tempered glass.
All-new flipper parts kit is the answer for sluggish flipper assemblies. 8/1993-10/1998
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
Williams / Bally regular cabinet stainless steel lockdown bar...
Standard 28-1/2 inch ribbed pinball machine leg with chrome plated finish for Williams...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Backbox lock and plate assembly for all of the Williams and Bally WPC syst...
Nylon flipper bushing is used on Williams Pinball games
New PINSKIN� brand pinball covers provide storage protection from UV rays.
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
High quality steel plate replaces Bally / Williams part #01-11400-1
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Flipper return and drop target return spring
Standard Williams / Bally battery holder with through hole circuit board mount terminals.
WPC Power Driver board rebuild kit
Williams original style white plastic pop bumper body
Flipper & shaft - Williams logo white
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
Pushbutton 1-1/8 inch red with internal spring
Metal yoke fits all pop bumper ring and rod assemblies.
27 inch long Black Plastic LIFT TRIM used on the bottom of the backglass.
Side rail set Williams/Bally 47 inch stainless
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Trough anti magnetic shim - Williams/Bally upgrade
Black lock with one key, lock washer, 1inch cam, and screw. Used for b...
Application Specific Integrated Circuit (ASIC) chip for Williams/Bally WPC
WING SCREW or WING BOLT used on late model WPC system games.
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Gray foam protector pre-cut pads commonly used in target switches...
Spring - barrel compression shooter black
Red transparent pop bumper cap
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Compression spring used in many different assemblies. Replaces 266-500...
Fiber yoke fits all pop bumper ring and rod assembles.
New replacement WPC Type 2 Electronic / Opto flipper boards
Reset Fix Board WPC Power Driver
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Standard backglass lift trim with 3/16 inch channel. Trim as needed. Used in...
Pin-Buddy™ combo kit
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Red star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Spring - barrel compression shooter brass