Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Barrel shaped, bright finish shooter spring used on many brand...
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
3 terminal, dual winding flipper coil is used on the following games:...
Standard pinball playfield tempered glass.
Designed for non-Fliptronic® 2/1988 - 8/1991 Williams and Bally machines...
Cabinet flipper leaf switch assembly for most non-solid state flipper circuits.
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
Williams / Bally regular cabinet stainless steel lockdown bar...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Backbox lock and plate assembly for all of the Williams and Bally WPC syst...
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Replaced by 77-PCR
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
High quality steel plate replaces Bally / Williams part #01-11400-1
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Flipper return and drop target return spring
Common spring for pinball machine ball shooter assemblies.
Standard Williams / Bally battery holder with through hole circuit board mount terminals.
WPC Power Driver board rebuild kit
Williams original style white plastic pop bumper body
Metal Oxide Varistor (MOV), 130 Volt Used in the input power line.
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
New style, black plastic, 3 AA cell, circuit board mounted battery holder.
Metal yoke fits all pop bumper ring and rod assemblies.
27 inch long Black Plastic LIFT TRIM used on the bottom of the backglass.
Side rail set Williams/Bally 47 inch stainless
Refurbished Williams transformer with connectors. Reference: 5610-12...
Black lock with one key, lock washer, 1inch cam, and screw. Used for b...
Application Specific Integrated Circuit (ASIC) chip for Williams/Bally WPC
Gray foam protector pre-cut pads commonly used in target switches...
Spring - barrel compression shooter black
Red transparent pop bumper cap
Reset Fix Board WPC Power Driver
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
Pin-Buddy™ combo kit
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Red star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Spring - barrel compression shooter brass
Cashbox nest bracket Williams
35 a wire lead bridge rectifier 5100-09690-00
Yellow wrapper 2.2 uF @ 250 volt axial lead non-polarized metalized polyester. 125-5002-00
21 piece electronic components rebuild kit for the High Voltage section.
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
