Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Heavy duty 3 prong grounded 15 amp 110v AC power cord replacement plug
Barrel shaped, bright finish shooter spring used on many brand...
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
Standard pinball playfield tempered glass.
Standard keyed-alike single bit 7/8 inch long barrel lock with chrome bezel fi...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Commonly used pop bumper skirt, or wafer, used in all contemporary machines
Backbox latch hex key wrench tool for Data East / Sega / Stern
Common solenoid coil with no diode.
14 piece power supply connector rebuild kit fpr Data East / Williams boards
Black plastic cashbox used in most solid state pinball machines
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
This is the battery holder used on late model Stern (1998 and newer) and S...
Rectifier board Williams Sys 3-11A / Data East / Sega
Plunger and link assembly for many Williams/Bally and other manufacturer p...
Spring - barrel compression shooter black
Coil - solenoid with diode (SA = SG)
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
Data East / Sega / Stern flipper solenoid coil with diode.
Pin-Buddy™ combo kit
USE AE-23-800-01 as an equivalent substitute
Spring - barrel compression shooter brass
Shorter barrel spring for ball shooter assembly on all Data East, Sega, an...
Rubber grommet used on many Vertical Up Kicker (VUK) and Knocker assemblies.
Diagnostic Eprom for all Data East pinball CPU
Pinball Event Tune-Up Kit
Spring washer 1/2 inch inner diameter and 3/4 inch outer diameter commonly used on...
Pin-Buddy™ Game Saver Cantraption&tm 45°
Data East / Sega coil stop bracket
Hole guard - switch slot 1-1/4 inch
E-63 switch with micro roller. REPLACES the 180-5119-00 and 180-5119-01
Data East / Sega/ Stern flipper coil
Sega / Data East / Stern Playfield black plastic playfield glass support R...
Data East and early Sega plunger and crank assembly
Glass corner protectors - Set of 2
E-clip or e-ring commonly used on many mechanisms. 20A-8712-25 270-5002-00
Pinball machine volume control 10K potentiometer with long shaft
Sub-miniature snap action switch with fork Y-lever actuator. Replaces 180-...
Machine Screw 6-32 x 3/8" long phillips pan head with external tooth lockw...
Knocker/ kickback plunger assembly used in ball launch assembly 500-5477-01
Plunger & link assembly for later Bally and Williams machines.
5 VDC motor and gearbox assembly used in 1993 Data East JURASSIC PARK pinball.
Universal PPB board for all Data East / Sega / Stern 520-5021-XX boards.
Made in the USA factory original SILICONE based elastomer lamp covers
Flipper bushing DE/Sega/Stern 1/4 inch ID notched
Metal post with hex base 6-32 top and 10-32 thread on bottom.
Standard 7/8" long chrome finish barrel lock with 3 digit adjustable combination
Spring used on relay for VUK and Lazer Kicker.
Integrated Circuit 2K by 8 CMOS static 24 pin RAM chip. Replaces 5340-09878-00
Slingshot assembly leaf switch...
Data East/Sega/Stern solenoid coil 24-940 with diode on top (OT)
IC - 28 pin DIP NVRAM FM1608-120
Microswitch - ramp and high scoop.
Acetate instruction/score card cover 3.25 x 6 inches
Pin-Buddy™ Game Saver Cantraption™ 180°
