Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Ten-bulb box of #44 high quality miniature incandescent lamps.
Heavy duty 3 prong grounded 15 amp 110v AC power cord replacement plug
Barrel shaped, bright finish shooter spring used on many brand...
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
Standard keyed-alike single bit 7/8 inch long barrel lock with chrome bezel fi...
All-new flipper parts kit is the answer for sluggish flipper assemblies. 8/1993-10/1998
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
Ten-bulb box of #555 high quality miniature lamps
Standard 28-1/2 inch ribbed pinball machine leg with chrome plated finish for Williams...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
High quality steel plate replaces Bally / Williams part #01-11400-1
Key hook used on most coin door interiors.
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Ten-bulb box of #89 high quality miniature incandescent lamps.
Standard pinball machine leg leveler with 3/8 inch -16 thread and 3 inch long shaft
Flipper return and drop target return spring
Standard Williams / Bally battery holder with through hole circuit board mount terminals.
Williams original style white plastic pop bumper body
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Metal Oxide Varistor (MOV), 130 Volt Used in the input power line.
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
New style, black plastic, 3 AA cell, circuit board mounted battery holder.
Pushbutton 1-1/8 inch red with internal spring
Metal yoke fits all pop bumper ring and rod assemblies.
Ten-bulb box of #906 High quality miniature incandescent lamp. May be replaced with 05-906W LED or 04-0912 bulbs.
Plunger and link assembly for many Williams/Bally and other manufacturer p...
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Application Specific Integrated Circuit (ASIC) chip for Williams/Bally WPC
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
WING SCREW or WING BOLT used on late model WPC system games.
Gray foam protector pre-cut pads commonly used in target switches...
Spring - barrel compression shooter black
Red transparent pop bumper cap
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
New replacement WPC Type 2 Electronic / Opto flipper boards
Pin-Buddy™ combo kit
Clear star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Williams / Bally black plastic drop target with 3/8" wide wedge shaped top...
Spring - barrel compression shooter brass
Complete Ball Shooter assembly fits most Bally/Williams and other machines.
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
Pinball Event Tune-Up Kit
Large twist-in socket for #906 wedge base lamps.
