Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Heavy duty 3 prong grounded 15 amp 110v AC power cord replacement plug
Barrel shaped, bright finish shooter spring used on many brand...
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
3 terminal, dual winding flipper coil is used on the following games:...
Standard pinball playfield tempered glass.
Standard keyed-alike single bit 7/8 inch long barrel lock with chrome bezel fi...
Designed for non-Fliptronic® 2/1988 - 8/1991 Williams and Bally machines...
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
Williams / Bally regular cabinet stainless steel lockdown bar...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Commonly used pop bumper skirt, or wafer, used in all contemporary machines
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Replaced by 77-PCR
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
Key hook used on most coin door interiors.
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Ten-bulb box of #89 high quality miniature incandescent lamps.
Standard pinball machine leg leveler with 3/8 inch -16 thread and 3 inch long shaft
Flipper return and drop target return spring
Standard Williams / Bally battery holder with through hole circuit board mount terminals.
Williams original style white plastic pop bumper body
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Metal Oxide Varistor (MOV), 130 Volt Used in the input power line.
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
HD Anti-reflection Glass playfield 21 x 43 x 3/16 inch
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
Metal yoke fits all pop bumper ring and rod assemblies.
Ten-bulb box of #906 High quality miniature incandescent lamp. May be replaced with 05-906W LED or 04-0912 bulbs.
Plunger and link assembly for many Williams/Bally and other manufacturer p...
27 inch long Black Plastic LIFT TRIM used on the bottom of the backglass.
Side rail set Williams/Bally 47 inch stainless
Plastic cube style, circuit board mounted DPDT (double pole, double throw)...
Gray foam protector pre-cut pads commonly used in target switches...
Spring - barrel compression shooter black
Williams / Bally dual contact flipper pushbutton cabinet switch
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
Pin-Buddy™ combo kit
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Red star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Williams / Bally black plastic drop target with 3/8" wide wedge shaped top...
Spring - barrel compression shooter brass
Cashbox nest bracket Williams
35 a wire lead bridge rectifier 5100-09690-00
Yellow wrapper 2.2 uF @ 250 volt axial lead non-polarized metalized polyester. 125-5002-00
Pinball Event Tune-Up Kit
Playfield glass protector black rubber grommet used on aprons
Large twist-in socket for #906 wedge base lamps.
