Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Ten-bulb box of #44 high quality miniature incandescent lamps.
Heavy duty 3 prong grounded 15 amp 110v AC power cord replacement plug
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
3 terminal, dual winding flipper coil is used on the following games:...
Standard keyed-alike single bit 7/8 inch long barrel lock with chrome bezel fi...
All-new flipper parts kit is the answer for sluggish flipper assemblies. 8/1993-10/1998
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
Ten-bulb box of #555 high quality miniature lamps
3 terminal, dual winding replacement flipper coil for the following Willia...
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Backbox lock and plate assembly for all of the Williams and Bally WPC syst...
Nylon flipper bushing is used on Williams Pinball games
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
High quality steel plate replaces Bally / Williams part #01-11400-1
Key hook used on most coin door interiors.
Common solenoid coil with no diode.
Ten-bulb box of #89 high quality miniature incandescent lamps.
Flipper return and drop target return spring
WPC Power Driver board rebuild kit
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Metal Oxide Varistor (MOV), 130 Volt Used in the input power line.
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
New style, black plastic, 3 AA cell, circuit board mounted battery holder.
Ten-bulb box of #906 High quality miniature incandescent lamp. May be replaced with 05-906W LED or 04-0912 bulbs.
Plunger and link assembly for many Williams/Bally and other manufacturer p...
27 inch long Black Plastic LIFT TRIM used on the bottom of the backglass.
Side rail set Williams/Bally 47 inch stainless
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Black lock with one key, lock washer, 1inch cam, and screw. Used for b...
Application Specific Integrated Circuit (ASIC) chip for Williams/Bally WPC
WING SCREW or WING BOLT used on late model WPC system games.
Gray foam protector pre-cut pads commonly used in target switches...
Reset Fix Board WPC Power Driver
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
Compression spring used in many different assemblies. Replaces 266-500...
Pin-Buddy™ combo kit
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Lockdown bar front trim used on all late model wide cabinet size Bally / Williams machines
Williams / Bally black plastic drop target with 3/8" wide wedge shaped top...
Cashbox nest bracket Williams
35 a wire lead bridge rectifier 5100-09690-00
21 piece electronic components rebuild kit for the High Voltage section.
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
Pinball Event Tune-Up Kit
Pushbutton 1 inch round yellow 'Start'
Large twist-in socket for #906 wedge base lamps.
Connector rebuild kit - Williams WPC CPU board
Black 7/8 inch diameter corrugated plastic slit hose sleeve for wiring harness protection
Williams/Bally backglass trim. For games that use translites.
