Head bolt 3/8-16 x 1-1/2 inch acorn head 5/8 inch
Kit allows you to replace the original CRT monitor with practically a...
Bolt carriage 8-32 x 1-1/4 inch black
Data East insert panel circuit board standoff with barbed end
Coin Door Security bar kit - no drill
Nail-on furniture glide allows sliding without cabinet damage. Flat beige plastic base.
T-Nut 10-32 x 7/16 x 3/4 inch base
Black finish special cabinet T-nut with hex drive end.
Slide & pivot support bracket right
Williams MEDIEVAL MADNESS pinball machine screw pin
T-nut 10-32 thread with black oxide
Flat black washer .465" outer diameter x .20" inner diameter x .032 thick.
Spiral nail .15 inch dia. x 1/2 inch tr-hd
Hinge assembly lower insert
Edge slide bracket used on Stern pinball machines
Bracket - insert hinge mounting
Dowel pin 3/32 x 7/16 inch
Peel & stick adhesive backed Kwik Klip cable and wire harness holder.
Carriage bolt 1/4-20 x 1-1/4" 4320-01123-20B
Button head fastener. Reference: 02-4546 Williams DEMOLITION MAN...
New, high quality brass finish 3/8-16 thread with 5/8 inch acorn head .
Slotted hasp plate/bar. Used on games such as Bally REVENGE FROM MARS...
Plastic strain relief bushing used for AC power cords
Hinge - pivot left --13 inch
Cable clamp 3/4 inch
Ball shooter mounting plate secures the ball shooter housing from inside t...
Hinge - pivot right - 13 inch
3/32" diameter x 3/8" length slotted spring roll pin. Reference: 20...
Screw #8 x 5/8" p-ph black
Sheet metal screw #8 x 1/2 inch sl-hwh-ab zinc
Locking cam plate - backbox & insert bd.
Spring washer 3/8" inner diameter and 1/2" outer diameter commonly used on...
Coin door security bar hasp staple bracket. Use with 01-14085.1 hinge bracket.
Hex head bolt with 3/8-16 thread and 2 " overall length used to securepi...
Hex head bolt with 3/8-16 thread and 3-1/2 inch overall length used to secure pinball backbox to lower cabinet.
New black baked-enamel ball shooter cover for most late model Bally/Willia...
Bracket - insert stop
Cable clamp 1-1/2 inch single hole mount
Spring clip for Gottlieb tilt bob.
Nut - spacer hex 1/2" OD 1/4-20 x 1/2 inch
Bolt carriage 10-24 x 5/8 inch black
Bolt carriage 10-24 x 1-1/4 inch black
Post fastener 2 1/16 inches long with 8-32 thread on both ends and a hex nut
Coin door security bar hasp hinge bracket. Use with 01-14086.1 staple brac...
Hex head bolt with 3/8-16 thread and 4-1/2 inch overall length used to secure pinball backbox to lower cabinet.
Playfield service support slide U bracket upgrade kit for late model Stern SPIKE and SPIKE 2 System pinball machines.
Replacement smooth wire rod used in the swinging pendulum tilt mechanism
Snap rivet - plastic 1/8 x 1/8 inch
Metal pivot bracket for Gottlieb pinball machines. Reference: 25657...
Tilt wire with hook 4.75 inch overall
lever guide assy
Metal spacer 1/2 x 3/8 inch
Hex head bolt with 3/8-16 thread and 3" overall length used to securepin...
Pivot Nut 7/16 inch Reference: 02-4244
Machine Screw 8-32 x 1-3/4 inch p-ph
Bracket - slide backbox insert latch
Slide and pivot support bracket for left side. Used on Stern pinball ma...
Fish paper insulator for terminal strips. Reference: 01-12299
Backbox hinge set Data East 11.5 inch
Carriage bolt 10-24 x 1-3/4 inch course thread size
