WING SCREW or WING BOLT used on late model WPC system games.
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
42 piece set of stainless steel hardware for late electromechanical and ea...
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Cashbox nest bracket Williams
Tamper resistant head screw nail or spiral nail - 0.10 dia X 3/4 inch long
Flat washer used in ball shoooter assemblies .390 x .625 x .059 inch.
Common tilt plumb bob with 0.15 inch interior diameter for rod.
Back box toggle latch 20-9347 or tension latch
Special short neck black carriage bolt for cabinet / backbox hinge.
Pivot nut 7/8 inch
PAL nut 5/8 inch. Replaces 02-3000 & 240-5003-01
Tilt plumb bob assembly
Rivnut hex 3/8-16 x .845 inch
Cable clamp 1 inch diameter single
Pivot nut 1/2 inch. Reference: 02-4329
Tinnerman clip used to secured the plumb bob tilt on late model tilt assemblies.
Backbox lock plate for Williams/Bally WPC System game backbox locks...
Bubble level vial commonly used in Williams / Bally pinball machines...
Leg bolt 3/8-16 X 2-3/4 inch acorn head black
Hinge assembly upper insert
Pivot nut 11/16 inch
Bally shooter lane arch bracket is made from pre-polished stainless steel...
This is the left side Playfield Slide Assembly used on all late model Wil...
Washer 0.265 inch x .500 inch x .067 inch
Tamper resistant head screw or spiral nail 0.10 diameter X 1 inch
Playfield prop up rod for early Bally pinball machines. Reference:...
Plate - spacer pinball machine cabinet slide. Reference: 01-11408
Bolt carriage 10-24 x 2-1/4 inch black
Cable clamp 1/2 inch diameter single
Bracket clip for many late model Bally / Williams WPC machines. Refere...
Plumb bob tilt wire is used on many Bally Williams and other machines.
New high quality brass finish 3/8-16 thread with 5/8" acorn head with 2-1/2 inch length.
Bracket door release assembly for Bally DOCTOR WHO pinball machine
Cable clamp Holder 1/4" diameter
Circuit board mounting bracket for under playfield boards.
Cable clamp 3/4 inch diameter single
Hex head bolt with 3/8-16 thread and 2-1/2 inch overall length
Kit allows you to replace the original CRT monitor with practically a...
Coin Door Security bar kit - no drill
Black finish special cabinet T-nut with hex drive end.
Williams MEDIEVAL MADNESS pinball machine screw pin
Flat black washer .465" outer diameter x .20" inner diameter x .032 thick.
Slotted hasp plate/bar. Used on games such as Bally REVENGE FROM MARS...
Plastic strain relief bushing used for AC power cords
3/32" diameter x 3/8" length slotted spring roll pin. Reference: 20...
Coin door security bar hasp staple bracket. Use with 01-14085.1 hinge bracket.
Hex head bolt with 3/8-16 thread and 2 " overall length used to securepi...
New black baked-enamel ball shooter cover for most late model Bally/Willia...
Cable clamp 1-1/2 inch single hole mount
Post fastener 2 1/16 inches long with 8-32 thread on both ends and a hex nut
Coin door security bar hasp hinge bracket. Use with 01-14086.1 staple brac...
Hex head bolt with 3/8-16 thread and 4-1/2 inch overall length used to secure pinball backbox to lower cabinet.
Machine Screw 8-32 x 1-3/4 inch p-ph
Fish paper insulator for terminal strips. Reference: 01-12299
3/32" diameter x 5/8" length slotted spring roll pin. Reference: 20...
This is the right side Playfield Slide Assembly used on all late model Wi...
Hex head bolt with 3/8-16 thread and 4 inch overall length.
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/4 inch length.
