Medium-high tension spring used on pinball machine ball shooter assemblies.
21 piece electronic components rebuild kit for the High Voltage section.
35 a wire lead bridge rectifier 5100-09690-00
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
Playfield glass protector black rubber grommet used on aprons
Black 7/8 inch diameter corrugated plastic slit hose sleeve for wiring harness protection
Large twist-in socket for #906 wedge base lamps.
Plunger assembly 3.375 inches no hole
Connector rebuild kit - Williams WPC CPU board
Upgraded Trough Assembly for Williams / Bally pinball machines
Williams/Bally backglass trim. For games that use translites.
Pinball Event Tune-Up Kit
Williams/Bally opto board set
Bell armature or plunger assembly for ball kickers and poppers
Pin-Buddy™ Game Saver Cantraption&tm 45°
Elastic Stop Nut used on rod and ring (A-4754) assemblies.
Infrared Transmitter assembly in the white plastic housing.
Playfield side rail plastic molding is 42-1/4"
Sub miniature snap action switch with 3 terminals and custom wireform.
Knocker assembly kit for Bally and Williams AE-23-800
Clear tempered 27 x 18-7/8 x 1/8 inch thick glass
Pop bumper bracket used on Williams / Bally machines and other brands.
Capacitor 15,000 mf 25 volts. Suitable replacement for 5040-12313-00.
Flat washer used in ball shoooter assemblies .390 x .625 x .059 inch.
Fits shaft diameter of 3/8 inch with groove diameter of 5/16 inch.
Common tilt plumb bob with 0.15 inch interior diameter for rod.
E-clip or e-ring commonly used on many mechanisms. 20A-8712-25 270-5002-00
Hole guard - switch slot 1-1/4 inch
Glass corner protectors - Set of 2
Back box toggle latch 20-9347 or tension latch
Made in the USA factory original SILICONE based elastomer lamp covers
Backglass trim kit - Williams WPC/System 11
Left side flipper unit Plunger- link-crank assembly
Williams WPC pinball system Fliptronic II complete flipper mechanism. Includes FL-11630 coil.
Common solenoid coil used on many manufacturers pinball machines.
Playfield post fastener 6-32 top thread 1/4" long 8-32 bottom thread 3/8 inch
Machine Screw 6-32 x 3/8" long phillips pan head with external tooth lockw...
Red pop bumper skirt, or wafer, used in most manufacturers' pop bumper.
Lever guide and and locking assembly used to secure front lockbar
30 inch 14 pin 2 connector Data & Control ribbon cable with Display to Do...
Standard snap-in Nyliner® bearing bushing with 1/4 inch Inner Diameter
AC Line cord cover for WPC Bally/Williams pinball machine cabinets.
Williams/Bally opto InfraRed transmitter board used in LED assembly A-1690...
6-32 thread tee nut with 1/4 inch barrel height, 3-prong, 19/32 inch base
Wire 1/4" ground braid
New opto board 10 LED assembly. Replaces A-20246
5-1/4 inch 4 ohm 25 watt speaker
Metal post with round base 6-32 tap and 10-32 thread on bottom.
Compression spring used on pop bumper assemblies and others.
Universal snap action submicroswitch with 4 inch wire actuator that can be formed to various shapes.
Plunger & link assembly for later Bally and Williams machines.
Elastic stop nut used on the thumper bumper brackets and other mechanisms.
Lamp socket with bracket holds wedge based bulbs such as #555
.156" spacing 12 position Insulation Displacement style connector
Special short neck black carriage bolt for cabinet / backbox hinge.
Popular red LED used on many machines including: Bally ATTACK FROM M...
Slingshot crank arm assembly
Flipper opto plastic interruptor BLACK
Spring - extension diverter plunger
Williams/Bally pop bumper plunger. Reference: 02-3406-1 2A-340...
