Hole guard - switch slot 1-1/4 inch
Black rubber grommet, bumper plug. Reference Numbers: Williams #2...
Bridge rectifier CM3501 DB3501
Lane guide - 2-1/8 inch red A-9394
3/4 inch diameter pinball is used in many pinball and pitch & bat machines.
Leaf switch assembly pop bumper dual right tie SW-11A-35-1
Compression spring used on pop bumper assemblies and others.
Universal snap action submicroswitch with 4 inch wire actuator that can be formed to various shapes.
Elastic stop nut used on the thumper bumper brackets and other mechanisms.
Miniature switch with flat actuator lever.
Williams/Bally pop bumper plunger. Reference: 02-3406-1 2A-340...
Mini post 8-32 thread Reference: 02-4003
6-1/2 inch speaker has 8 ohm impedance with 6 oz magnet. 6-1/4 inch diameter.
Diode - 1.1 volt 1 amp DO-41
Set of 4 standard black durable processed smooth finish 28-1/2 inch ribbed leg.
E-clip or e-ring commonly used on many 3/16" mechanism shafts
Common solenoid coil used on many manufacturers pinball machines. May...
Yellow pop bumper skirt, or wafer, used many manufacturers' pop bumper ass...
New production flash lamp resistor board is used under the playfield board 5768-11096-00
Flipper coil stop for 1987 Williams F-14 TOMCAT, SPACE STATION, FIRE!, BIG...
Pin-Buddy™ Game Saver Cantraption™ 180°
Williams plunger and link assembly with 2-1/8 inch long plunger
New bare metal 28-1/2 inch long Williams style leg ready for your own painting...
3 bank push button Service / Diagnostic switch assembly with center latching switch.
System 9-11 Flipper Power Supply 50v
Nylon coil sleeve - 2-1/16 inch
Capacitor 0.01mf 50v +80-20 axial
Williams right side flipper crank, plunger and link assembly for early flippers
Leaf switch - lane change normally open right
Williams left side flipper crank, plunger and link assembly
Playfield stud with wood screw bottom and 6-32 machine thread top.
1/8" diameter x 7/16" length slotted spring roll pin. Reference:...
Round .093 inch dia. male Molex connector pin terminal
Black 10-32 X 3/8 hex socket head cap screw...
Rivnut hex 3/8-16 x .845 inch
Standard pinball playfield Invisiglass.
Latch plated used with tension latch 20-9347 to secure backbox.
Test Fixture Williams System 9-11 lamp matrix
Extension spring. Reference: 10-362
Single fuse holder with molded base holds 1/4" x 1-1/4" pinball machine f...
NVRAM replacement for 6116, 6264 RAM ICs
10' long 3 wire grounded AC power cord with stripped ends.
Power Supply board United/Williams/Data East D-8345
Coil retainer bracket
Williams / Bally flipper link bushing installed between flipper link and crank.
5 watt 10 ohm ceramic power resistor used on many flash lamp boards.
Left and right side stainless steel trim molding for early Williams pinball machines.
Eject cam arm
Axial capacitor 0.1UF 50v +/-20 axial Z5U temperature coefficient.
3 position plug uses .093" diameter crimp terminals.
Machine screw with 6-32 thread and 3/16" long with phillips pan head and attached lockwasher.
Spring plate assembly for kickout holes. Use with A-6948-L assembly
Washer 0.265 inch x .500 inch x .067 inch
Complete ball eject assembly for Williams/Bally pinball machine-right side.
Pin-Buddy™ Game Saver Cantraption™ 45° BLUE
Resistor - 330 ohms 7 watts with radial leads. Used on many flash lamp boa...
Pin-Buddy™ Game Saver Cantraption™ 45° RED
Coil stop bracket for target mechanisms.
Compression spring.
