DEMOLITION MAN (Williams) Backbox tech chart
Pin-Buddy™ Game Saver Cantraption™ 45° Red TRANSLUCENT
DEMOLITION MAN (Williams) Coil sleeve kit
.100 inch 12 Position male molex header. Reference: Williams 5791-12461...
.125 in diameter x 5/8 in length slotted spring roll pin. Reference:...
Common solenoid coil used on many manufacturers pinball machines...
Foam rubber protector 3-5/8 inches long - black
4-1/2" wire ball guide fits Williams DEMOLITION MAN and other machines.
Coin door interface board WPC
Rivet - .125 x .187 x .218 inch brass
1/4 inch stud x 20 threads per inch x 1-1/2 inch length coarse thread carriage bolt
Machine screw with 2-56 thread and 3/16 inch long with phillips pan head and integrated internal tooth lockwasher.
E-clip or e-ring commonly used on many mechanisms. 7/16 in. Replaced by 20-8712-43
Switch gate bracket for Bally/Williams pinball machines...
E-clip or e-ring commonly used on many mechanisms. 7/16 in. measured at the o...
Flipper crank bolt with flat 90 degree notch washer modified for use on flipper pawl.
Post round 10-32 x 4.62 inch 8-32 tap
Connector IDC 7r mt/end 22/.100
DEMOLITION MAN (WMS) Ball popper weldment
Williams Bracket Assy.
Playfield Invisiglass for Wide Body pinball machine measures 23-3/4 x 43 x 3/16 inches
IC - 14 pin DIP 74HC125 buffer/line driver
Williams DEMOLITION MAN left rear wall.
Williams DEMOLITION MAN pinball machine ramp #2 left guard bracket. Re...
Pop bumper body Williams 36mm yellow transparent
female pin
Target oblg stat-op yellow plastic only
Williams DEMOLITION MAN Wire Ramp.
Bracket - switch gate. Reference: 01-9587
Bracket & switch assembly
New design replacement fliptronic board which replaces A-15028 and A-15...
Williams DEMOLITION MAN switch gate assembly. Reference: A-13487
Pop bumper body Williams 36mm red
Mechanical meter board assembly with cable. Reference: A-15275-1
DEMOLITION MAN (Williams) Wire ramp
Pin-Buddy™ Game Saver Cantraption™ 45° GLOW IN THE DARK WHITE
Williams DEMOLTION MAN stainless steel welded feed ramp assembly.
.100 Z header mass term lock-t
IC - 16 pin DIP 74HC138 CMOS 3-8 line dec/demp
Williams DEMOLITION MAN Wireform Ramp.
IC - 14 pin DIP SN74F08N quad AND gate 2 input
Bolt carriage #10-24 x 7/8 inch black
11 x 17 inch original 2 sided fold out full color factory sales sheet for Wil...
Twin nut plate - switch stack. Replaced by 01-9321
Pop bumper body Williams 36mm orange transparent
Wire ball gate. Reference: 12-6958
DEMOLITION MAN (Williams) Ramp guard #3 left
12-6909 wireform. Reference: 12-6909
Right half metal gun handle of the right cabinet side control DEMOLITION MAN.
DEMOLITION MAN (Williams) ramp guard #2 right
WMS Metal Striker Plate.
Fish paper terminal insulator
opto cable - square
WMS new old stock Demolition Man Silver Claw.
Switch bracket assembly. Reference: A-18171
wire 18awg brn/blk
Machine Screw 8-32 x 5/8 inch ph t-r Torx®
Elevator guide shaft for Williams DEMOLITION MAN.
Swemmer NVRAM replacement for 6264 RAM ICs
Header .100 inch 5 position right angle lock
