Resistor SIP 10 pin 470 ohms x 9r
1/8" diameter x 3/4" length slotted spring roll pin
Kicker switch sub assembly
Insulator - thermistor
74HCT374 Integrated circuit 14 pin DIP Octal 3-State Noninverting Transparent Latch.
Sheet Metal Screw #4 x 1/2 inch pop bumper cap black
Light board lay-down socket. Use 24-8805
Foam rubber protector 1-1/2 inches long - black
Motor & Gear Housing part #14-7993 for Williams DEMOLITION MAN.
4 position Female Housing receptacle with no mounting ears uses .062 inch crim...
Sheet Metal Screw #8 x 5/8 inch p-rh
Washer .146 x .375 x .032 inch
Lock Washer #10 internal tooth-black
DEMOLITION MAN (Williams) Elevator opto
Plunger for flipper assembly 2-1/4 inch long
Right side ball eject assembly used in Williams DEMOLITION MAN and T2.
Lit Frames 90s Williams-Bally
Zinc plated hex nut 10-24 thread.
8r mt/end 18/156
Machine Screw 6-32 x 3/4 inch p-ph-sems 232-5300-00
DEMOLITION MAN (Williams) pinball machine manual. March 1994. ORIGINAL
DEMOLITION MAN (Williams) Cryoclaw motor
6 position female housing receptacle with no mounting ears uses .062 inch crimp terminals
Lamp holder assembly for large base bayonet bulb such as #89. Replaced by 077-5100-00
Williams DEMOLITION MAN pinball machine ramp decal. Reference: 31-192...
Bracket - slide support
Crystal 8.0 MHz Reference: 5520-10438-00
Target switch L bracket 95° red
Nut 8-32 esn NM stop nut black
Williams DEMOLITION MAN pinball machine playfield plastic "Start A...
Machine Screw 8-32 x 1" pl-hh-s USE 4008-01003-16
Ball gate bracket Bally/Williams
Terminal strip assembly used in WPC Williams/Bally series games Referen...
6 position plug uses .062" crimp terminals.
Williams DEMOLITION MAN pushbutton.
This is the pair of slingshot plastics for Williams DEMO MAN.
Nut 3/8-16 esn stop nut M-319-7
DEMOLITION MAN (Williams) Plastic set
D.C.motor control & spacer assembly
67 piece white rubber ring kit for Williams DEMOLITION MAN pinball machine includes...
Bally / Williams pinball machine 2 pin solenoid coil connection cable
Slotted 1/4" hes head machine screw with 8-32 thread x 1-1/4" long with...
IC - 3 pin TO-92 5v regulator LM78L05
6r mt/end 18/156
Machine Screw 6-32 x 3/16 inch p-ph
15 position receptacble with no mounting ears uses .093 inch crimp terminals.
Foam rubber protector 14 inches long - black
Machine screw 6-32 thread x 3/8 inch long. Replaced by 4006-01003-06
Machine screw with 4-40 thread and 3/8" long with phillips pan head and in...
Cable mini switch
New 128 x 32 LED Dot Matrix Display module for pinball machines
Hex washer head 8-32 thread x 3/4" long machine screw.
rollover sw assy w/zinc Bracket
Assortment of 6 different value fuses customized for Williams DEMOLITION M...
Switch mounting plate for Bally/ Williams WPC System pinball machines.
Fish paper insulator for terminal strips. Reference: 01-12299
IDC 13-position .156 inch (3.96mm) THRU connector 22awg
Machine screw with 6-32 thread and 7/8" long with phillips round head...
Fliptronic II board Williams WPC
67 piece black rubber ring kit for Williams DEMOLITION MAN pinball machine includes...
