Washer .172 x .437 x .059 inches
Hex socket head cap screw has 10-32 partial thread and length of 1-1/4 inches.
Zinc plated stopnut 10-24 thread with nylon insert.
Zinc plated 8-32 x 1-3/4 inch long unslotted hex washer head machine screw.
nut 5-40 hex
Red IDC Connector - 3R mt end 22/156
9 pin connector uses .093 inch crimp terminals
Connector IDC 12r mt/end 22/.100
Safety switch bypass device for servicing Bally/Williams WPC System games.
Standard snap-in Nyliner® bearing bushing with 1/4 inch Inner Diameter
Capacitor 470 pf @ 100v axial measures .1" diameter x .1" wide x .2" lengt...
Connector IDC 9r mt/end 22/.100
4 position plug uses .062" crimp terminals.
New design opto receiver board. Replaced by A-18244-GLM
Bracket - interlock dual switch
Left side flipper crank assembly. Reference: A-17050-L 01-8073-L...
Integrated circuit MPU 2105kp - 40 adsp
Washer .203 x .437 x .032 inch
Williams/Bally wire gate use in the WPC series pinball machines. R...
Flat black washer .465" outer diameter x .20" inner diameter x .032 thick.
Sheet Metal Screw #6 x 1-1/4 inch p-flh-a
Black finish 10-32 x 1/4 inch set screw with locking compund patch. 3/32 inch drive.
Spring - extension lever guide
Rivet - 1/8" diameter x 1/2"
11mm x 66.2mm plunger used on divertor mechanisms.
Switch mounting bracket with 3/16 inch mounting holes
Outlet-iec conn 237 socket. Reference: 5851-13867-00
3 position receptacle with no mounting ears uses .062" crimp terminals.
Wire hinge pin. Reference: 12-6882-1
Lamp socket - long bracket
Hinge assembly lower insert
Williams DEMOLITION MAN pinball machine elevator assembly.Includes: 14...
Lock washer #6 split
Right side flipper crank assembly. Reference: A-17050-R 01-8073-R...
Tilt weight blade assembly. Used in Williams/Bally WPC series pinball mac...
Washer .265 x .500 x .015 inches
15 position connector with ears uses .093" crimp terminals. Reference:...
Machine screw 8-32 thread x 3/8 inch long phillips round head. Replaced by 4008-01003-06
Zinc plated hex nut with 10-32 thread.
Spring plate assembly for kickout holes. Use with A-6948-R assembly.
Button head fastener. Reference: 02-4546 Williams DEMOLITION MAN...
Pin-Buddy™ Game Saver Cantraption™ 45° Neon Green Translucent
8r mt/thru 22/156
Pop bumper body Williams 36mm clear
Spacer
6r mt/end 22/.100
Sheet metal screw - Phillips flat head, Zinc plated steel, #6 x 1/2 inch long.
Williams pinball machine metal front ball trough bracket
Pin-Buddy™ Game Saver Cantraption™ 45° YELLOW
Wire gate
Zinc plated 8-32 thread x 1/2 inch long unslotted hex washer head machine screw.
Switch blade with contact assembly commonly used in WPC pinball machines...
Crystal 32.768 Khz dt38 Reference: 5520-12084-00
Bally / Williams ramp diverter assembly kit
Cement resistor 0.12 Ohm 10W 5% Tolerance Reference: 5012-12632-00
Bracket - coil mount
2r mt end 22/156
Cap screw 10-32 x 7/8 inch socket head.
Bracket - cashbox lock
Flat washer .361" x .500" x .059" thick.
