3 position plug uses .093" diameter crimp terminals.
Lamp holder assembly. Reference: A-17835
Normally closed EOS used on various assemblies.
LED complete conversion kit for Williams DEMOLITION MAN pinball machine.
One of the most commonly used screws in Williams/Bally pinball machines.
6-32 X 1-1/2" black spiral fin shank steel screw.
Stop nut 8-32 thread.
Single inline 10 pin resistor network 4.7k 9r 10 5%
Common knocker coil bracket used in many Williams games.
9 position Insulation Displacement Connector (IDC).
Opto board 7 way A-15576 A-15595 5768-12921-05
Zinc-plated steel rivet -1/8 inch shaft diameter x 5/32 inch long
Machine Screw full thread 6-32 x 1-3/4 zinc plated phillips pan head...
Miniature snap action switch with 3 terminals and custom wireform.
Rivet - 1/8 x 1/4 inches nickel
Connector - 7 position insulation displacement style with passthrough...
2 position connector uses .062 inch crimp terminals.
Washer 0.265 inch x .500 inch x .067 inch
Williams DEMOLITON MAN pinball machine Police Car model. Reference:...
Capacitor 15,000 mf 25 volts snap mount. Suitable replacement for 5040-12313-00.
1/4" tall barrel and 8-32 thread with 19/32"" base or flange.
Pin-Buddy™ Game Saver Cantraption™ 45° BLUE
Kicker mounting bracket used on many Williams and Ball/Williams pinball ma...
E-clip or e-ring commonly used on many mechanisms. 7/16 in. measured at the o...
Dot Matrix Display fish paper rear shield for WPC-95 games.
Pin-Buddy™ Game Saver Cantraption™ 45° RED
2 position plug with no mounting ears uses .093" crimp terminals.
Logic power cable for Williams WPC pinball machines. Reference: H-15...
Plate - spacer pinball machine cabinet slide. Reference: 01-11408
Integrated circuit 16 pin DIP AD-1851 16 bit mono audio PCM.
22-1/8 inch long foam rubber protector for widebody pinball machine front trim moldings.
Machine Screw 8-32 x 3/4" TPR Security Torx® - pan head 4008-01093-12B
13 position Insulation Displacement Connector (IDC).
Bolt carriage 10-24 x 2-1/4 inch black
Machine screw 8-32 thread x 3/8" long phillips flat head.
15 in long 26 pin 2 connector Data & Control ribbon cable
Bracket - WPC playfield service support
Nut 4-40 thread with elastic stop.
7 transistor opto receiver board
Williams coil bracket used on most late model Williams and Bally/Williams.
Cable clamp 1/2 inch diameter single
Pushbutton 1 inch round yellow 'Extra Ball'
Black plastic spacer 0.250" Length
14 leg SOIC package 74LS14 Inverter with Schmitt Trigger integrated circuit.
Battery 1.5v AA alkaline for CPU board memory.
#5 sheet metal screw 5/8 inch long is used to secure EOS on flipper assemblies...
Thermostat 85° C with leads 5644-09368-00
Brass slotted machine screw 10-32 thread 5/8" long.
Socket IC PLCC 84 pin
Bracket clip for many late model Bally / Williams WPC machines. Refere...
Machine Screw 8-32 x 1" TPR Torx - pan head. T-15
Washer - zinc plated- 0.125 x .281 x .032 inch rivet back
Machine screw with 4-40 thread and 5/8" long with phillips pan head
Opto holder - white
Yoke metal - pop bumper substitute 01-5492
Bracket - speaker panel latch
Switch mounting bracket with 3/16 inch mounting holes
#10 steel split lock washer. Zinc plated.
Ball gate & wire assembly
The most common sheet metal / wood screw in late model pinball machines. T...
