Black plastic spacer #6 x 0.541 inch tall
Opto transmitter & receiver packaged in U-shaped black plastic housing.
Coil Plunger
Latch plated used with tension latch 20-9347 to secure backbox.
#6 Truss head zinc plated machine screw 1/2 inch long.
6-32 nut used on Williams flipper plates to secure flipper bushings.
Lockbar lever guide assy complete - no spring
Bolt is 1/4-20 thread x 1-1/4" long and used in machines such as: BUGS...
Machine screw with 6-32 thread and 3/8 inch long with phillips pan head.
Machine screw 8-32 x 3/8 inch phillips pan head.
Extension spring used on late model Williams/ Bally playfields
Cable clamp 1 inch diameter single
Fuse - time delay 4 amp (5.0mm x 20mm) - Box of 5. Reference Willia...
Handle pushbutton switch assembly
Refurbished Williams transformer with connectors. Reference: 5610-13...
Three terminal coil used in Bally / Williams pinball machines. Refere...
This is the small phillips panhead screw used to secure most playfield mic...
3 inch tweeter speaker used in backboxes of various pinball machines.
Machine Screw 10-32 x 5/8" p-ph-s
NVRAM replacement for 6116, 6264 RAM ICs
Post - 1-1/4 inch narrow red
10' long 3 wire grounded AC power cord with stripped ends.
Tape double sided .032 x 3/4 inch x 9 ft
Machine screw with 6-32 thread and 1/2 inch long with phillips pan head
Wing nut with 6-32 thread for plumb bob tilt assembly wire.
Post stud #8 x 1-1/2 inch wood screw USE 530-5010-01
3/8-16 x 1-1/4 inch round head long rib neck carriage bolt
Drive arm assembly used in solid state Williams/Bally games.
Spring - extension - red eject
Coil retainer bracket
Bumper post with hex base with 8-32 threaded bottom with 6-32 top hole
Backbox lock plate for Williams/Bally WPC System game backbox locks...
Insulator - switch fishpaper
Dark gray perforated plastic vent screen
Entire ball kicker assembly kit includes coil, grommet, armature etc.
Switch Mounting Bracket. Reference: 01-9375
Flipper spring steel lever 4 inch
Black plastic spacer #6 X 0.343 inch tall
Williams/Bally pinball machine RIGHT playfield slide assembly.
This all-new flipper parts kit is the answer for sticky, sluggish, weak...
Post - plastic double star clear- 1-1/2 inch
Jet bumper coil bracket assembly includes AE-26-1200 coil, yokes, plunger, spring, fasteners.
Hinge assembly upper insert
Williams DEMOLITION MAN pinball machine floating eyeball. Reference:...
#8 x 1/2" indented hex washer head screw with piercing tip
Integrated circuit opto isolator 4N25 NTE3040 SK2040
Integrated circuit 3a DMOS bridge driver for motor control.
6-1/2 inch outer diameter 4 ohm woofer speaker used in many pinball machine and video cabinets
Rivet - 1/8" diameter x 1/8" nickel
Bracket used on Williams and Bally kicker assemblies.
Standoff clip
IDC orange connector 7R mt/end 18/156. Reference: 5792-10818-07
32 inch 26 pin 2 connector Display Data & Control ribbon cable.
Lamp socket and diode assembly
Clip for vinyl switch covers. Reference: 01-10636
Dot matrix controller board WPC
Williams plunger and link assembly with 2-1/4 inch long plunger.
Keps nut 6-32 with attached external tooth lockwasher.
Rivet - 1/8 inch shaft diameter x 7/32 inch shaft length. 7/32 oval head
Axial capacitor 0.1UF 50v +/-20 axial Z5U temperature coefficient.
