Pushbutton 1 inch round yellow 'Start'
Upgraded Trough Assembly for Williams / Bally pinball machines
Connector rebuild kit - Williams WPC CPU board
Bell armature or plunger assembly for ball kickers and poppers
Williams/Bally opto board set
Transparent red eject hole shield plastic with 3/16" (0.1875") holes.
Elastic Stop Nut used on rod and ring (A-4754) assemblies.
Pin-Buddy™ Game Saver Cantraption&tm 45°
Infrared Transmitter assembly in the white plastic housing.
Playfield side rail plastic molding is 42-5/16"
Sub miniature snap action switch with 3 terminals and custom wireform.
AC Power Cord - 15 foot stripped end
Knocker assembly kit for Bally and Williams AE-23-800
Pop bumper bracket used on Williams / Bally machines and other brands.
Clear tempered 27 x 18-7/8 x 1/8 inch thick glass
Capacitor 15,000 mf 25 volts. Suitable replacement for 5040-12313-00.
Common tilt plumb bob with 0.15 inch interior diameter for rod.
#8-32 top thread and #8-32 bottom thread with 5/16 inch hex collar steel/zinc.
E-clip or e-ring commonly used on many mechanisms. 20A-8712-25 270-5002-00
Williams/ Bally WPC Spare Semiconductors Kit
Back box toggle latch 20-9347 or tension latch
Left side flipper unit Plunger- link-crank assembly
Made in the USA factory original SILICONE based elastomer lamp covers
Backglass trim kit - Williams WPC/System 11
Williams WPC pinball system Fliptronic II complete flipper mechanism. Includes FL-11630 coil.
Playfield post fastener 6-32 top thread 1/4" long 8-32 bottom thread 3/8 inch
Pinball Event Tune-Up Kit
Common solenoid coil used on many manufacturers pinball machines.
Replacement grey, flexible vinyl sub-microswitch cover
Machine Screw 6-32 x 3/8" long phillips pan head with external tooth lockw...
30 inch 14 pin 2 connector Data & Control ribbon cable with Display to Do...
Standard snap-in Nyliner® bearing bushing with 1/4 inch Inner Diameter
Hole guard - switch slot 1-1/4 inch
Williams/Bally opto InfraRed transmitter board used in LED assembly A-1690...
AC Line cord cover for WPC Bally/Williams pinball machine cabinets.
6-32 thread tee nut with 1/4 inch barrel height, 3-prong, 19/32 inch base
5-1/4 inch 4 ohm 25 watt speaker
Metal post with round base 6-32 tap and 10-32 thread on bottom.
Wire 1/4" ground braid
Compression spring used on pop bumper assemblies and others.
Universal snap action submicroswitch with 4 inch wire actuator that can be formed to various shapes.
Plunger & link assembly for later Bally and Williams machines.
Elastic stop nut used on the thumper bumper brackets and other mechanisms.
.156" spacing 12 position Insulation Displacement style connector
Slingshot crank arm assembly
Popular red LED used on many machines including: Bally ATTACK FROM M...
Flipper opto plastic interruptor BLACK
Williams/Bally pop bumper plunger. Reference: 02-3406-1 2A-340...
Spring - extension diverter plunger
Williams Motor Controller board assembly. Also used in: TWILIGHT ZONE...
9 position Insulation Displacement Connector (IDC) 22 ga 9R MT/END 22/156
Minipost - plastic red 1 inch tall.
34 pin 3-3/4 inch long 2 connector ribbon cable used for CPU to Driver Board c...
Upgraded, reinforced, front mounted, stationary target used on...
Infrared receiver assembly in the black plastic housing.
Red twist-lock plastic min dome for flash lamps. 550-5030-02
Flap - ball gate
The "H" channel is the black plastic trim between backglass and...
Williams / Bally white plastic opto interrupter used on flipper cabinet opto boards. Replaced by 03-9001
