Standard carbon steel 1-1/16 inch diameter, 80 gram case hardened pinball
Dot matrix display (DMD) for pinball machines
Standard carbon steel 1-1/16" diameter, 80 gram pinball
Leg bolt 3/8-16 thread with 5/8 inch acorn head and 2-1/2 inch length.
3 terminal, dual winding flipper coil is used on the following games:...
All-new flipper parts kit is the answer for sluggish flipper assemblies. 8/1993-10/1998
2-3/16 x 1/2 inch coil sleeve. Replaces 545-5388-00
3 terminal, dual winding replacement flipper coil for the following Willia...
Pop bumper (jet bumper, thumper bumper) ring and rod assembly.
Commonly used pop bumper skirt, or wafer, used in all contemporary machines
Universal Ball Shooter rod with black plastic knob. Used on all Williams /...
Backbox lock and plate assembly for all of the Williams and Bally WPC syst...
Plastic thickness gauge for adjusting flipper bushing gap
Common compression spring used on flippers, pop bumper, ball kickers, ball poppers.
Williams/Bally WPC system standard domestic 2 chute Coin Door with WPC adapter.
High quality steel plate replaces Bally / Williams part #01-11400-1
Rear black plastic playfield glass trim molding used on most Bally/Williams games.
Common solenoid coil with no diode.
Flipper return and drop target return spring
WPC Power Driver board rebuild kit
Williams original style white plastic pop bumper body
Flipper & shaft - Williams logo white
Universal NVRAM replacement for 5101, 6116, 6264 RAM ICs
Slingshot switch used on many brands of electronic pinball machine kicker. Replaces SW-1A-114.
Small twist-in wedge base socket for #555 wedge base lamps. Replaces 077-5007-00
Sub miniature snap action switch with 3 terminals and custom wireform actuator.
Leg bolt 3/8-16 x 2-3/4 inch acorn head 5/8 inch
New style, black plastic, 3 AA cell, circuit board mounted battery holder.
Metal yoke fits all pop bumper ring and rod assemblies.
Pushbutton 1-1/8 inch red with internal spring
27 inch long Black Plastic LIFT TRIM used on the bottom of the backglass.
Side rail set Williams/Bally 47 inch stainless
Trough anti magnetic shim - Williams/Bally upgrade
Black lock with one key, lock washer, 1inch cam, and screw. Used for b...
This is a flipper unit END OF STROKE (EOS) switch used on Williams / Bally...
Application Specific Integrated Circuit (ASIC) chip for Williams/Bally WPC
Gray foam protector pre-cut pads commonly used in target switches...
3/8-16 hex machine screw nut, steel & zinc 5/8 across flats
This is the standard pop bumper socket with solid flat 4" leads used in all Bal...
Fiber yoke fits all pop bumper ring and rod assembles.
Compression spring used in many different assemblies. Replaces 266-500...
New replacement WPC Type 2 Electronic / Opto flipper boards
Reset Fix Board WPC Power Driver
Hairpin retaining clip used to secure shafts and studs on many mechanical assemblies.
Pin-Buddy™ combo kit
Thermistor - 8amp 2.5 ohm R25 The thermistor is installed in the power...
Later style coil stop used in Williams/Bally games from 08/1993 to 06-1999...
Coil sleeve - 2-1/16 inch with 3/16 inch flange
Red star post 1-1/16 inch common to late model Bally / Williams and other brand pinball machines.
Williams/ Bally 02-4352 hex socket T-Nut Pivot Bushing with 1/2" shaft, 3/...
Lockdown bar front trim used on all late model wide cabinet size Bally / Williams machines
Cashbox nest bracket Williams
Williams / Bally style lane guide (also referred to as Rollover Guides, L...
21 piece electronic components rebuild kit for the High Voltage section.
Common 6 inch speaker used in cabinet bottoms of Williams/ Bally games.
Black 7/8 inch diameter corrugated plastic slit hose sleeve for wiring harness protection
Large twist-in socket for #906 wedge base lamps.
Plunger assembly 3.375 inches no hole
Pushbutton 1 inch round yellow 'Start'
Connector rebuild kit - Williams WPC CPU board
